📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Found this in my parts selection. I don’t know if it’s a specific radio part or an aftermarket item. Almost looks like some sort of channel board, but I’m just guessing. I have no information or paperwork I can find.

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Was using the radio this morning working fine then something happened now just about 2 watts on Am and about 2 watts on ssb both lower and upper. Radio dead on frequency and receive is great No burn marks on the bottom pc side. I pulled bothe finals 2sc 1969 and 2sc2166 abd both are ok. Seem like rf out power just dropped…

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Hello Team, I was troubleshooting low drive of Turner Plus Three when used with Drake TR-4. The issue was that I had to dial mic preamp and rx gain on the radio to the maximum to get reasonable RF output on the wattmeter. The transceiver was working just fine with Shure 444, so the issue was definitely the Turner mic. I replaced all…

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale I have an icon sm30 desk mic hooked up to an Icom IC 7300 and when I key the mic it makes a noise inside the radio. Kind of like a relay bouncing back and forth very quickly. Only while the switch is in motion. Is anybody familiar with this problem?

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale What do you all use for magnification for working on through hole board type of work? Net necessarily smt type of microscope but thinking loupe glasses or something. My eyes have gotten to the point readers just don’t cut it anymore.

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Putting my new operating position together. Currently have 3 Astron 50A linear supplies, each driving 8012 Rig Runners (or with their companion transceivers wired directly to the supply terminals). Need an option for the VHF/UHF bench. There are a few brick type amplifiers (CPI HF150, Mirage/RF Concepts 6, 2, 222, 432) in my inventory. Power out anywhere from 100 to around 400w PEP-…

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Hi all I received a Sears amplified desk Mic looks like a turner plus 3 B but all plastic and totally different guts not working someone had their fingers in it looking for a schematic or pics of the inside of anybody has one Thank You

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Hi. Anyone have a schematic for a Grant XL? Searching only turned up a user manual. Thanks.

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale Just wired up a SSK for my Stryker and noticed it has noise when keyed. A hissing, rushing noise. I would appreciate ideas. Recap?? Here is a video of the problem.

📌 INFORMATIVA COPYRIGHT — I diritti appartengono al legittimo proprietario. Fonte: worldwidedx.com — 🔗 Leggi l’articolo originale OKay.. as the title says the radio wants to smoke (it won’t blow a 4 amp fuse) itself when switched into SSB mode, I measured the voltage at the collectors of driver and final, and when I switch the radio to SSB the voltage shunts to ground and the current draw increase, a lot. This is in RX mode, it’s enough to blow…